D2S1-02GD41C1D 2GB Dual channel 2.5" SATA 4000 Solid State Flash Disk, Innodisk

Industrial Storage // memorydepot.com

2GB Dual channel 2.5" SATA 4000 Solid State Flash Disk D2S1-02GD41C1D

Industrial SATA Solid State Flash Disk

2GB

Industrial SLC SATA Solid State Flash Disk
Commercial Temp

The SATA Solid State Disk is the next generation of storage device based on industrial flash memory technology, which emulates an ordinary magnetic hard disk.

Built for speed, these Solid State Storage Devices need no moving or spinning parts, and that makes no mechanical noise, suitable for used in portable or embedded system, which has only limited power consumption. The Flash Disk Drive products are also free from extra and special algorithm or some firmware driver. Just plug the unit into the SATA slots and operate it as same as a regular Hard Disk Drives.

These high-speed SSD units provide faster and higher performance storage solution for industrial application, embedded computing, high-speed networking, broadband communications, mobile computing, military, medical and aerospace

In Addition of high-performance, the devices are capable of withstanding a higher dree of enivornmental distress, delivering extreme endurance.

Model variation

Industrial Temperature -10 +70

Wide Temp -40 +85

PRICING AND PRODUCT DETAILS

InnoDisk FiD 2.5 SATA4000 products provide high capacity flash memory Solid State Drive (SSD) that electrically complies with Serial ATA (SATA) standard. InnoDisk FiD 2.5 SATA4000 support SATA I standard (1.5Hz) with high performance. Sustain read is 37MB(Max) per second, and sustain write is 34MB(Max) per second. InnoDisk FiD 2.5 SATA4000 uses standard 2.5-inch form factor, which can be used in laptop. InnoDisk FiD 2.5 SATA4000 is also designed for industrial field.

The SSD have good performance, and have small latency time. It effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). InnoDisk FiD 2.5 SATA4000 can work in harsh environment. The SSD is vibration resistance, and can work in lower or higher temperature than HDD. InnoDisk FiD 2.5 SATA4000 complies with ATA protocol, no additional drives are required, and the SSD can be configured as a boot device or data storage device.

General Specifications

	Burst Transfer Rate : 1.5GB/sec Sustained Read : Duel Channel: 37MB/sec Single Channel: 20MB/sec Sustained Write : Duel Channel:34MB/sec Single Channel: 20MB/sec Average Latency : 0.4 ms DC Input Voltage: +3.3V/+5V Single power supply Dimension: 99.88/69.63/9.3 mm (W/T/H) Compatibility: CE and FCC standards

Boot

No additional device drivers are required. Flash in Disk (FiD) 2.5 SATA4000 can be configured as a boot device.

Wear Leveling

Flash memory can be erased within a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device. InnoDisk FiD 2.5 SATA4000 uses a wear-leveling algorithm to ensure that consecutive writes of a specific sector are not written physically to the same page/block in the flash. This spreads flash media usage evenly across all pages, thereby extending flash lifetime.

Environmental Specifications

Operating Temperature Range
Standard Grade: -10⁰C ~ +70⁰C
Industrial Grade: -40⁰C ~ +85⁰C
Storage Temperature Range
Standard Grade: -55⁰C to +95⁰C
Industrial Grade: -55⁰C to +95⁰C

Reliabily and Durability

Reliability Test Conditions
Vibration: 7 Hz to 700Hz, 2 g, 3 axes
Mechanical Shock Duration: 0.5ms, 1500 g, 3 axes
Drop Unit: From a height of 1.5 m
Product Condition MTBF (Hours): FiD 2.5 ATA6000 Telcordia SR-332 GB, 25 ⁰CC > 3,000,000

Manual CHS Value

Capacity	Cylinders	Heads	Sectors	LBA
128MB	249	16	63	250992
256MB	499	16	63	502992
512MB	999	16	63	1006992
1GB	1999	16	63	2014992
2GB	3965	16	63	3996720
4GB	7931	16	63	7994448
8GB	15863	16	63	15989904